Altronix OLS20 Installation Instructions Manuel d'utilisateur télécharger pdf

Overview:

OLS20 power supply/charger converts 115VAC / 60Hz input, into a 12VDC @ 1 amp or 24VDC @ .5 amp of

continuous supply current (refer to specifications). This general purpose power supply has a wide range of application

for access control and security system accessories that require additional power.

Specifications:

Input:

• 115VAC / 60Hz, .5 amp.

Output:

• 12VDC or 24VDC selectable operation.

• .5 amp continuous supply current @ 24VDC

1 amp continuous supply current @ 12VDC.

• Filtered and electronically regulated outputs.

• Short circuit and thermal overload protection.

Battery Backup:

• Built-in charger for sealed lead acid or gel type batteries.

•

Maximum charge current .5 amp.

• Automatic switch over to stand-by battery when AC fails.

Additional Features:

• AC input and DC output LED indicators.

• Includes battery leads.

Board Dimensions (approximate): 2.6”W x 3.1”L x 1.3”H

Specified at 25˚ C ambient.

Voltage Output Selection Table:

Output VDC Switch Position Max. Load DC

12VDC SW 1 - Closed 1.2 amp

24VDC

SW1 - Open .5 amp

Installation Instructions:

The OLS20 should be installed in accordance with The

National Electrical Code and all applicab

le Local Re

gulations.

1. Mount the OLS20 in desired location/enclosure.

2. Set the OLS20 to desired DC output voltage via SW1

(refer to Voltage Output Selection Table).

3. Connect AC power to connector #1

(Fig. 1) (black & white flying leads) and ground (green flying lead)

Use 18 AWG or larger for all power connections(Battery, AC input).

Keep power limited wiring separate from non-power limited wiring (115VAC / 60Hz Input, Battery Wires).

Minim

um .25” spacing m

ust be pr

vided.

4. Measure output voltage before connecting devices. This helps avoid potential damage.

5. Connect devices to be powered to terminals marked [-- DC +]

(Fig. 1).

When the use of stand-by batteries are desired, they must be lead acid or gel type.

Connect battery to terminals marked [-- BAT +]

(Fig. 1).

Use two (2) 12VDC batteries connected in series for 24VDC operation.

Note: When batteries are not used a loss of AC will result in the loss of output voltage.

For continuous protection against fire replace fuse with the

same type and rating 5mm - 20mm, 250V, 2A

OLS20 - Offline Power Supply/Charger

MADE IN USA

LGN

--- BAT +

pen - 24V

Closed - 12V

CONNECTOR #1

Gr WhBk

PTC2

--- DC +

2A



250V

Fig. 1

1 2

Résumé du contenu

Page 1 - CONNECTOR #1

Overview:OLS20 power supply/charger converts 115VAC / 60Hz input, into a 12VDC @ 1 amp or 24VDC @ .5 amp of continuous supply current (refer to specif

Page 2 - Terminal Identification:

MADE IN USALGN--- BAT +Open - 24VClosed - 12VSW1DCPTC2VR1AC--- DC +LED Diagnostics:Red (DC) Green (AC) Power Supply Status ON ON Normal operating cond

Commentaires sur ces manuels

Pas de commentaire

Altronix OLS20 Installation Instructions Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour les appareils électriques Altronix OLS20 Installation Instructions. Altronix OLS20 Installation Instructions User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour les appareils électriques Altronix OLS20 Installation Instructions