Altronix AL175ULX Installation Instructions Manuel d'utilisateur télécharger pdf

Overview:

The AL175ULX is a power limited power supply/charger that will convert 115VAC / 60Hz input, into two individually

PTC protected 12VDC or 24VDC outputs, (see specifications). It is intended for use in applications requiring UL Listing

for Access Control System Units (UL 294) and applications requiring an interface with Fire Alarm Control Panels.

Specifications:

Power Supply Output Specifications:

Output VDC Switch Position Max. Stand-by Load DC Max. Alarm Load DC Battery (optional)

12VDC SW1 Open 1.75 amp 1.75 amp 12VDC

24VDC SW1 Closed 1.75 amp 1.75 amp 24VDC

Stand-by Specifications:

Output 4 hr. of Stand-by &

5 Minutes of Alarm

12VDC / 7 AH Battery Stand-by = 1.25 amp

24VDC / 7 AH Battery Alarm = 1.25 amp

Installation Instructions:

The AL175ULX should be installed in accordance with article 760 of The National Electrical Code or NFPA 72 as well

as all applicable Local Codes.

See Terminal Identification Chart on page 3 for a description of each terminal function.

1. Mount the AL175ULX in desired location.

Connect

C po

er to the b

lack and white flying leads of the transformer. Secure green wire lead to earth ground.

Use 18 AWG or larger for all power connections (Battery, DC output). Use 22 AWG to 18 AWG for power

limited circuits (trigger inputs, dry outputs).

Keep power limited wiring separate from non-power limited wiring (115VAC / 60Hz Input, Battery Wires).

Minimum .25” spacing must be provided.

3. Set the AL175ULX to the desired DC output voltage by setting switch SW1 to the appropriate position

(refer to Power Supply Output Specification Table).

Agency Listings:

• UL Listed for Access Control Systems (UL294).

CUL Listed - CSA Standard C22.2

No.205-M1983, Signal Equipment.

• MEA - NYC Dept. of Buildings Approved.

• CSFM - California State Fire Marshal Approved.

• Conforms to NFPA 101 life safety codes

Input:

• Input 115VAC / 60 Hz, .6 amp.

Output:

• Selectable 12VDC or 24VDC power limited outputs.

• Class 2 Rated power limited outputs.

• 1.75 amp continuous supply current

@ 12VDC or 24VDC.

• Filtered and electronically regulated output.

• Short circuit and thermal overload protection.

Battery Backup:

• Maximum charge current: 400mA.

• Automatic switch over to stand-by battery when

AC fails.

Supervision:

• AC fail supervision (form "C" contacts).

• Dry trigger output (form "C" contacts).

Fire Alarm Interface:

• Dry trigger input.

Visual Indicators:

• AC input and DC output LED indicators.

Added Features:

• Includes power supply, transformer

and enclosure.

Enclosure Dimensions:

13”H x 13.5”W x 3.25”D

Product Weight:

8.9 lbs.

AL175ULX

Access Control Power Supply/Charger

v. L13Y7

1 2 3 4

Résumé du contenu

Page 1 - AL175ULX

Overview:The AL175ULX is a power limited power supply/charger that will convert 115VAC / 60Hz input, into two individuallyPTC protected 12VDC or 24VDC

Page 2 - LED Diagnostics:

4. Measure output voltage before connecting devices. This helps avoid potential damage.5.Connect one (1) 12VDC battery toterminals marked [+ BAT --] (

Page 3 - TOP ONLY

Terminal Identification:Terminal Function/DescriptionLegendTRG1 & TRG2 These input terminals are designed to connect to the normally closedoutputs

Page 4 - Typical Application Diagrams:

Fig. 5 - Latching fire alarm tie-in with manual reset:Fig. 3 - Typical dual mag lock installation with fire alarmtie-in using trigger controlled outpu

Commentaires sur ces manuels

Pas de commentaire

Altronix AL175ULX Installation Instructions Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour les appareils électriques Altronix AL175ULX Installation Instructions. Altronix AL175ULX Installation Instructions User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour les appareils électriques Altronix AL175ULX Installation Instructions